ElectraSeal ESD Control Concrete Sealer

Anti Static, Economical, Long Life and Beautiful Shine

 

ESD floor photo of Seattle WA projectToday's reality dictates an increasingly daunting task. To meet the latest ANSI ESD static control standards and assure your successful manufacturing of static sensitive electronics esd flooring is a must! Does it make since to pay $7.00 to 10.00 per installed square foot for ESD tiles, thick set ESD epoxy or an anti-static rubber floor? Most think NOT! ElectraSeal seals concrete with an effective static control formulation designed to meet today's latest requirements and eliminate dust production from the concrete slab at an Economical Price!

 

WHY A STATIC CONTROL CONCRETE SEALER?

Value, Performance and Longevity. A typical concrete slab will post fairly good electrical conductivity due to the moisture content of the concrete.  Unfortunately this electrical conductivity fluctuates dramatically with the ambient humidity and moisture content of the slab. In addition, unsealed concrete is dusty, absorbs contaminants such as oils and liquids and ends up being a time consuming maintenance nightmare!

 

RELIABLE ANTI STATIC PERFORMANCE, OUTSTANDING VALUE!

concrete coated with anti static esd conductive sealer

concrete sealer makes any floor anti-static arrowPermanent static control performance!

conductivity compliant to many esda specifications arrowEliminates concrete dusting!

economical esd flooring sealer for static control floorsClean, high tech glossy appearance.

EsD Flooring, Static Control Mats, ESD Ionizer ArrowEconomical yet durable and long lasting.

static control concrete sealer, economical and long lasting esd flooringLOW Odor, LOW VOC's (<55). Meets new green building standards! ElectraSeal is designed for use on unsealed, indoor, cast in place concrete slabs but will bond to a variety of sealed and unsealed concrete (pretesting is always recommended).

 

APPLICATION IS FAST, EASY AND LOW ODOR!

Best results are obtained when ElectraSeal is applied to cured concrete slabs which are 60 Deg F. or warmer and in relative humidity conditions of < 50%. Remove nuisance dust by sweeping with a soft bristle broom. A sweeping compound that does not contain oil may be used if needed. Thoroughly vacuum slab to remove any remaining loose dirt or dust.  If contaminants such as oil and grease have soaked into the slab wash with ElectraClean rinse slab and allow to dry completely prior to application of ElectraSeal. Three coats will provide the optimum gloss and durability. Apply thin even coats using new loop end rayon or other non linting finish mops, allowing ElectraSeal to dry, (depending on humidity and temperature) for approximately 60 minutes between coats. Typical life span of product is approximately 3 years and dependent on traffic and maintenance. ElectraSeal may be effectively recoated without removal.

 

EASY TO MAINTAIN!

ElectraSeal is an extremely durable Anti Static concrete sealer. After application and curing of ElectraSeal routine maintenance is all that is required to maintain the luster and conductivity of the finish.  Remove abrasives that can scratch and degrade the floor by dry mopping (usually on a daily basis).  Damp mop or auto scrub with ElectraClean and water as needed.

 

SPECIFICATIONS

Note: The following specifications pertain to the product as applied to indoor, unsealed, cast in place, on grade concrete flooring slabs.

 

Nonvolatile Solids

22% +/- 0.5%

Total Active

26.5%

ESD S7.1 (PTP and RTG) @ 100 VDC

<1.0E09 @ 40% Relative Humidity

Gallon Coverage (Feet 2 )

 Approximately 1500 (sf) per gallon per coat

VOC Emissions per EPA Test Method 24

< 55 grams per liter

Static Dissipation

< 0.02 Second

pH

8.4 - 9.0

Gloss 60 0

85+ @ 3 coats

Color

Translucent white

Weight Per Gallon

10 Lbs.

Slip Resistance (ASTM)

0.65 Minimum (excellent)

Stability

2 year minimum at room temperature

Freeze/Thaw Stability

3 cycles minimum

Drying Time Between Coats

1 Hour

Water Resistance

Good

Abrasion Resistance, ASTM D968-17

6,480 grams
Shelf Life 2 years in tightly sealed contaminate free containers stored at an ambient temperature of 70 degrees F. +/- 10 degrees F. Do not store containers in direct sunlight. Do not allow to freeze / thaw.

 

COVERAGE & AVAILABILITY

Typical coverage: 1,500 to 2,000 SF per gallon per coat

Authorized Distributor